Ampere Meter

Our range of IM 2501 ampere meter is integrated with a set point to control the rectifier. Meter operates a relay, when some amount of charge is made to pass. This relay is basically used to shut off from the rectifier and are used in the completion of the job.

IM2501, we offer is one of the well known common models and designed for the measurement in charge which is basically for electroplating bath. External shunt is responsible for direct input and also calculates the charge via circuit frequently.

Features of IM2501 are as follows:

• Dust proof membrane keypad
• One set point with relay output rated 230 V / 5 A (resistive)
• Ampere Hour / Ampere Minute selection
• Shunt value programmable at 75mV
• External Reset facility
• Retention of count in case of power failure

We offer IM 2502 ampere hour/minute meter which is advanced model of IM2501. Beside, from basic regular counting of ampere hour/minute or seconds, this one comes with totalizer. The totalizer is vital for all electroplating usages as this one manages the concentration of bath and also take care that over of additions of chemical. In addition to the, features of IM2501 like preset setting and relay output are integrating in this one as well. Moreover, there is an additional counter for total AH (ampere hour) or AM (ampere minutes) flowing through the circuit.

• Four plus 6 digit display
• Current (Ampere) display
• 6 digit totaliser
• 0.1 Ampere hour resolution for lower ampere shunt ratings
• One set point with relay output
• Memory retention in case of power failure

The IM 2503 model integrates wholesome electroplating control which is convenient for the users. Two relay outputs which is used for controlling the addition of chemicals including additives and brighteners. During the entire process more charge is taken from the bath which results in the decrease of net concentration. Count of totaliser tell about the charge which is being drawn from the bath. After assessing the count, the ampere hour could be managed in sync with which chemicals can be added.

Features:

• One set point with relay output rated 230 V / 5 A (resistive)
• Two relay outputs for doser control which operates on totaliser count
• Ampere Hour / Ampere Minute selection
• Ampere hour resolution for lower ampere shunt ratings
• Shunt value programmable at 75mV
• External Reset facility

@page { size: 8.5in 11in; margin: 0.79in } P { margin-bottom: 0.08in }

Ampere Hour Meter Module - Model TE 2504 is basically managed for ready setup or the usage can be seen in where the current requirements are low. This one is used which is ready to be applied in the stand alone panel and advanced form all the former models; IM2501, IM2502 and IM2503. These are basically panel mount instruments which are required to rectified in the rectifier or in an independent panel.

• Ready to use module, no extra wiring needed
• Additional high power relay provision
• Direct plug in socket for rectifier
• Audio / Visual alarm indication
• Banana plug terminals for connecting shunt
• Auto Manual switch for rectifier control

Our range of IM2509 model ampere hour meter is provided with three control relay outputs to facilitate addition of three chemicals. It should be noted that this feature is improvement over the IM2503 model which offers two control relay outputs to control addition of two chemicals.

Some of the features of this model are provided below: 

• 4 plus 6 digit displays for current flowing, totaliser and present ampere hour
• Three doser control relay outputs with programmable counts
• One set point with one control relay output
• Ampere hour / ampere minute selectable
• Shunt value programmable at 75 MV / 200 MV / 60 MV
• Ampere hour resolution for lower ampere shunt ratings
• Calibration output for ease of calibration

IM2513 Master Slave Ampere Hour Meter for Doser Control (Master/Slave Unit)

This model is apt for the plants where so many jobs take place in the by engaging independent rectifiers in common bath. This IM2513 model is basically master controller that is joined to numerous IM2502 ampere hour meters and make to the totaliser counts which are according to hour meter. Also, relies on the net count. This one also manage the two doser relay outputs and chemicals like additive and brightener to the bath.

 Features of this product are listed below:

• 6 digit ampere hour display
• Two relay outputs with set points for external doser control
• Up-to eight ampere hour meters can be connected
• Enable / disable of ampere hour meters connected
• Two wire RS485 interface between master and slave meters
• Distance up-to 500 to 1km between master and slave
• Connects up-to 8 ampere hour meters